Dealership Header Ray's Used Auto

Back to Search Results

Price: $7,000 2005 WOOD CHUCK HYROLLER 1200

  • Body:

    Engine: CAT

    Trans:

  • Drive:

    Ext. Color:

    Int. Color:

  • Mileage:

    Stock No: 1E-17

    VIN: 1W9RH15175G200429

12 Photos - Click Arrows to Advance Row

Play Video

Vehicle Inquiry

Vehicle interested in: 2005 WOOD CHUCK HYROLLER 1200

QUESTIONS ABOUT THIS VEHICLE?
Please list your questions in the Comments field below.

 
 
 
 
 
 
Please retype the characters from the picture
CAPTCHA
Change the CAPTCHA codeSpeak the CAPTCHA code
 

Features

Seller’s Comments

Weight: 5,200 Lbs.

Length: 14'6"

Width: 6'8"

Height: 8'2"

Noise Level: 80 decibels @ '50 feet, 360 degrees around the unit or less

Infeed Chute: 42" width, 31 1/2" height (Total of 1302 sq. in.) and 34" depth

Feed Roller Opening: 12" high x 17" wide opening

Feed Rollers: 23" circumference

Chipping Capacity: 12" diameter material

Folding Feed Table: 46" width, 32" depth. Total of 66" from the end of the folding feed table to the nip point of the feed rollers.

CHASSIS FRAME: 2" x 6" steel tubing with 'Is" wall.

AXLE:  7,000-lb. minimum capacity torsion type. Eight (8) lug pattern with E-Z Lube bearings shall be standard.

TRAILER BRAKES: 12-volt, self-adjusting type.

TIRES: (2) 245/75R16 radial tires mounted on 8 lug wheels.

FRONT JACK:  2,000-lb. capacity swivel side wind jack. Jack can be used to raise slide box. Rear jack is optional.

TOW BAR:  Tow bar shall be fixed steel. Pintle ring shall be 2 '/2" I.D.. minimum (or ball hitch) adjustable for height.

BATTERY BOX:  Battery box shall be a 14 gauge steel construction that is lockable and mounted directly to frame,

CHIPPER CUTTING DISC: 40" diameter x 2" thick A36 steel; machined for accurate balance with two (2) full knife pockets. Factory set operating speed is 1250 RPM.

DISC SHAFT: 1044 solid steel x 4" diameter at the disc hub.

DISC BEARINGS:  (2) 2 1/16" roller bearings, 4-bolt flange mounted, greasable and easily replaced. Front and rear bearings shall be spherical, high-speed roller bearings rated at:
Static 53,500#
Basic 32,400#
Radial 3,540# with a 20,000 hr. life service.

CHIPPER KNIVES: (4) double-edged, 4" wide x 7" long x 'Is" thick and comprised of A8 steel - mounted in two (2) knife pockets, 180 degrees opposite each other.

CHIPPER ANVIL: 4 1/2" x 1/2," thick x 13" long. High carbon solid steel anvil. The chipper anvil is adjustable and has four (4) usable cutting edges.

CHIPPER BLOWER SYSTEM: (2) "Power Pockets" f

DISCHARGE CHUTE: Rotate 360 degrees and be easily locked into convenient positions without tools.

HYDRAULIC FEED SYSTEM: (2) horizontally mounted hydraulic driven feed wheels. Hydraulic feed wheel motors - (2) 14 cubic inch capacity at 3000 PSI. IN FEED CHUTE: Chute opening is 42" wide x 31'/,' high with a total of 1323 square inches minimum.

FEED RATE: 100 Ft./Min. 'May vary depending on options, engine and customer request.

TONGUE WEIGHT:  250 lb. average (may vary)

Controls:  Located curbside to eliminate operator from standing in street for engine start-up and PTO engagement.

 

*********PRICE DOES NOT INCLUDE SALES TAX***********

Supersized Photos

Disclaimer